Valorisation of cotton post-industrial textile waste into lactic acid: chemo-mechanical pretreatment, separate hydrolysis and fermentation using engineered yeast.

BACKGROUND: The textile industry has several negative impacts, mainly because it is based on a linear business model that depletes natural resources and produces excessive amounts of waste. Globally, about 75% of textile waste is disposed of in landfills and only 25% is reused or recycled, while less than 1% is recycled back into new garments. In this study, we explored the valorisation of cotton fabric waste from an apparel textile manufacturing company as valuable biomass to produce lactic acid, a versatile chemical building block. RESULTS: Post-industrial cotton patches were pre-treated with the aim of developing a methodology applicable to the industrial site involved. First, a mechanical shredding machine reduced the fabric into individual fibres of maximum 35 mm in length. Afterwards, an alkaline treatment was performed, using NaOH at different concentrations, including a 16% (w/v) NaOH enriched waste stream from the mercerisation of cotton fabrics. The combination of chemo-mechanical pre-treatment and enzymatic hydrolysis led to the maximum recovery yield of 90.46 ± 3.46%, corresponding to 74.96 ± 2.76 g/L of glucose released, which represents a novel valorisation of two different side products (NaOH enriched wastewater and cotton textile waste) of the textile industry. The Saccharomyces cerevisiae strain CEN.PK m850, engineered for redirecting the natural alcoholic fermentation towards a homolactic fermentation, was then used to valorise the glucose-enriched hydrolysate into lactic acid. Overall, the process produced 53.04 g/L ± 0.34 of L-lactic acid, with a yield of 82.7%, being the first example of second-generation biomass valorised with this yeast strain, to the best of our knowledge. Remarkably, the fermentation performances were comparable with the ones obtained in the control medium. CONCLUSION: This study validates the exploitation of cotton post-industrial waste as a possible feedstock for the production of commodity chemicals in microbial cell-based biorefineries. The presented strategy demonstrates the possibility of implementing a circular bioeconomy approach in manufacturing textile industries.

Green energy innovation initiatives for environmental sustainability: current state and future research directions.

Worldwide, all countries have been facing the crisis of climate change problem. They have been addressing this issue by focusing on implementing green energy innovation initiatives and promoting a sustainable future through environmental sustainability. In this research study, we focus on examining the role of green finance through green energy innovations, which are taking place in several sectors across different regions to promote environmental sustainability. The study has analysed 152 articles on this research domain through a systematic literature review to understand the present state of existing knowledge. The current study examines the Scopus-indexed research articles from the time period 2002 to 2023. Six emerging themes have been examined to understand their development and the potential impact of green initiatives for environmental sustainability. Various institutional theories have been explored to understand their association with the investigated research area. The paper has discussed multiple challenges that need to be addressed for the speedy implementation of green innovations. Finally, future research questions have been proposed based on the findings from the extant literature and the existing research gaps.

Effects of C/N ratio on N2O emissions and nitrogen functional genes during vegetable waste composting.

Nitrous oxide (N2O) generation during composting not only leads to losses of nitrogen (N) but also reduces the agronomic values and environmental benefits of composting. This study aimed to investigate the effect of the C/N ratio on N2O emissions and its underlying mechanisms at the genetic level during the composting of vegetable waste. The experiment was set up with three treatments, including low C/N treatment (LT, C/N = 18), middle C/N treatment (MT, C/N = 30), and high C/N treatment (HT, C/N = 50). The results showed that N2O emission was mainly concentrated in the cooling and maturation periods, and the cumulative N2O emissions decreased as the C/N ratio increased. Specifically, the cumulative N2O emission was 57,401 mg in LT, significantly higher than 2155 mg in MT and 1353 mg in HT. Lowering the C/N ratio led to increasing TN, NH4+-N, and NO3--N contents throughout the composting process. All detected nitrification-related gene abundances in LT continued to increase during composting, significantly surpassing those in MT during the cooling period. By contrast, in HT, there was a slight increase in the abundance of detected nitrification-related genes but a significant decrease in the abundance of narG, napA, and norB genes in the thermophilic and cooling periods. The structural equation model revealed that hao and nosZ genes were vital in N2O emissions. In conclusion, increasing the C/N ratio effectively contributed to N2O reduction during vegetable waste composting.

Thermal hydrolysis alleviates polyethylene microplastic-induced stress in anaerobic digestion of waste activated sludge.

Microplastics are known to negatively affect anaerobic digestion (AD) of waste activated sludge. However, whether thermal hydrolysis (TH) pretreatment alters the impact of microplastics on sludge AD remains unknown. Herein, the effect of TH on the impact of polyethylene (PE) microplastics in sludge AD was investigated. The results showed that the inhibition of methane production by PE at 100 particles/g total solids (TS) was reduced by 31.4% from 12.1% to 8.3% after TH at 170 °C for 30 min. Mechanism analysis indicated TH reduced the potential for reactive oxygen species production induced by PE, resulting in a 29.1 ± 5.5% reduction in cell viability loss. In addition, additive leaching increased as a result of rapid aging of PE microplastics by TH. Acetyl tri-n-butyl citrate (ATBC) release from PE with 10 and 100 particles/g TS increased 11.5-fold and 8.6-fold after TH to 68.2 ± 5.5 µg/L and 124.0 ± 5.1 µg/L, respectively. ATBC at 124.0 µg/L increased methane production by 21.4%. The released ATBC enriched SBR1031 and Euryarchaeota, which facilitate the degradation of proteins and promote methane production. This study reveals the overestimated impact of PE microplastics in sludge AD and provides new insights into the PE microplastics-induced impact in practical sludge treatment and anaerobic biological processes.

The potential impact of the new 'Right to Repair' rules on electrical and electronic equipment waste: A case study of the UK.

Every year an estimated two million tonnes of waste electrical and electronic equipment (WEEE) are discarded by householders and companies in the United Kingdom (UK). While the UK has left the European Union (EU), its waste-related policies still mirror those of the EU, including the WEEE-related policies. Motivated by the recent introduction the so-called 'Right to Repair' policy for electrical and electronic equipment (EEE) across the EU and UK, this paper aims to demonstrate that, depending on the commitment and behavioural changes by the consumers and the government, the future of the WEEE management of the UK will vary. To this end, focusing on landfilled WEEE reduction we develop a generic system dynamics model and apply it to eleven WEEE categories. They depict the flow of EEE and WEEE representing the interaction among the stakeholders (e.g., consumers and producers of EEE) and relevant government regulations of the UK. Our four scenario analyses find that longer use of EEE and better WEEE collection seem to be effective in reducing landfilled WEEE, while more reuse and more recycling and recovery have negligible impacts, despite excluding the additional generation of landfilled WEEE as a result of recycling and recovery. Comparing with the business-as-usual scenario, one year longer EEE use and 10% more of WEEE collection could at maximum reduce landfilled WEEE by 14.05% of monitoring and control instruments and 93.93% of display equipment respectively. Backcasting scenario analyses reveal that significant efforts are required to reduce the targeted amounts.

Achieving water-floatable photocatalyst on recycled bamboo chopsticks.

Disposable bamboo chopsticks (DBCs) are difficult to recycle, which inevitably cause secondary pollution. Based on energy and environmental issues, we propose a facile strategy to fabricate floatable photocatalyst (fPC) coated onto DBCs, which can be flexibly used in water purification. The photocatalyst of titania and titanium carbide on bamboo (TiO2/TiC@b) was successfully constructed from TiC-Ti powders and DBCs using a coating technique followed heat treatment in carbon powder, and the fPC exhibited excellent photocatalytic activity under visible light irradation. The analysis results indicate that rutile TiO2 forms on TiC during heat treatment, achieving a low-density material with an average value of approximately 0.5233 g/cm3. The coatings of TiO2/TiC on the bamboo are firm and uniform, with a particle size of about 20-50 nm. XPS results show that a large amount of oxygen vacancies is generated, due to the reaction atmosphere of more carbon and less oxygen, further favoring to narrowing the band gap of TiO2. Furthermore, TiO2 formed on residual TiC would induce the formation of a heterojunction, which effectively inhibits the photogenerated electron-hole recombination via the charge transfer effect. Notably, the degradation of dye Rhodamine B (Rh.B) is 62.4% within 3 h, while a previous adsorption of 36.0% for 1 h. The excellent photocatalytic performance of TiO2/TiC@b can be attributed to the enhanced reaction at the water/air interface due to the reduced light loss in water, improved visible-light response, increased accessible area and charge transfer effect. Our findings show that the proposed strategy achieves a simple, low-cost, and mass-producible method to fabricate fPC onto the used DBCs, which is expected to applied in multiple fields, especially in waste recycling and water treatment.

Comparing the effects of Al-based coagulants in waste activated sludge anaerobic digestion: Methane yield, kinetics and sludge implications.

Due to its effectiveness and ease of application, the process of flocculation and coagulation is often used for pollution removal in wastewater treatment. Most of these coagulants precipitate and accumulate in waste activated sludge (WAS), and could negatively affect sludge treatments, as observed for anaerobic digestion. Nowadays, wastewater treatment plants (WWTPs) are widely discussed because of the current paradigm shift from linear to circular economy, and the treatments performed at the facility should be planned to avoid or reduce adverse effects on other processes. The aim of this study was to compare the impact of poly aluminum chloride (PAC) and aluminum sulfate (AS) on WAS anaerobic digestion, by feeding replicate serum reactors with different levels of coagulant (5, 10 and 20 mg Al/g TS). Reactors without the addition of any coagulants represented the control group. Results revealed that Al-based coagulants inhibited methane production, which decreased as the coagulant addition increased. The inhibition was much more severe in AS-conditioned reactors, showing average reductions in methane yield from 14.4 to 31.7%, compared to the control (167.76 ± 1.88 mL CH4/g VS). Analytical analysis, FTIR and SEM investigations revealed that the addition of coagulants affected the initial conditions of the anaerobic reactors, penalizing the solubilization, hydrolysis and acidogenesis phases. Furthermore, the massive formation of H2S in AS-conditioned reactors played a key role in the suppression of methane phase. On the other hand, the use of coagulant can promote the accumulation and recovery of nutrient in WAS, especially in terms of phosphorus. Our findings will expand research knowledge in this field and guide stakeholders in the choice of coagulants at full scale plant. Future research should focus on reducing the effect of coagulants on methane production by modifying or testing new types of flocculants.

Harnessing carboxymethyl cellulose and Moringa oleifera seed husks for sustainable treatment of a multi-metal real waste.

This study aimed to evaluate effective treatment strategies for laboratory waste with an initial pH of 1.0, containing Cr6+, Mn2+, Co2+, Fe3+, Ni2+, Cu2+, Zn2+, Sr2+, Hg2+, and Pb2+ ions, focusing on flocculation, precipitation, and adsorption techniques. The study utilized microparticles derived from Moringa oleifera seed husks (MS), cryogels of carboxymethyl cellulose (CMC), and hybrid cryogels combining CMC and MS (CMC-MS25 and CMC-MS50) as adsorbents. The optimal strategy involved raising the pH to 7 using NH4OH, leading to the partial precipitation of metal ions. The remaining supernatant was then passed through columns packed with the aforementioned adsorbents. Utilizing CMC-MS25 and CMC-MS50 adsorbents resulted in the simultaneous removal of over 90% of the targeted metal ions. The adsorption of Cu2+ ions onto the adsorbents was facilitated by electrostatic interactions between Cu2+ ions and carboxylate groups, as well as Cu-OH chelation, as confirmed by X-ray photoelectron spectroscopy. Under optimized conditions, the fixed-bed column adsorption capacity was determined as 88.2 mg g-1. The CMC-MS25 adsorbents proved reusable at least 5 times, with the recovered Cu2+ ions potentially suitable for other processes. The scalability and feasibility of producing these novel adsorbents suggest a promising, cost-effective solution for treating complex matrices and recovering high-value metals, as copper.

Does WASH FIT improve water, sanitation, and hygiene and related health impacts in healthcare facilities? A systematic review.

Introduction: Environmental health services (e.g., water, sanitation, hygiene, cleaning, waste management) in healthcare facilities are important to improve health outcomes and strengthen health systems, but coverage gaps remain. The World Health Organization and United Nations Children's Fund developed WASH FIT, a quality improvement tool, to help assess and improve environmental health services. Fifty-three countries have adopted it. However, there is little evidence of its effectiveness. This systematic review evaluates whether WASH FIT improves environmental health services or associated health outcomes and impacts. Methods: We conducted database searches to identify relevant studies and extracted data on study design, healthcare facility characteristics, and inputs, activities, outputs, outcomes, and impacts associated with WASH FIT. We summarized the findings using a logic model framework and narrative synthesis. Results: We included 31 studies in the review. Most inputs and activities were described qualitatively. Twenty-three studies reported quantitative outputs, primary WASH FIT indicator scores, and personnel trained on WASH FIT. Nine studies reported longitudinal data demonstrating changes in these outputs throughout WASH FIT implementation. Six studies reported quantitative outcomes measurements; the remainder described outcomes qualitatively or not at all. Common outcomes included allocated funding for environmental health services, community engagement, and government collaboration, changes in knowledge, attitudes, or practices among healthcare staff, patients, or community members, and policy changes. No studies directly measured impacts or evaluated WASH FIT against a rigorous control group. Conclusions: Available evidence is insufficient to evaluate WASH FIT's effects on outputs, outcomes, and impacts. Further effort is needed to comprehensively identify the inputs and activities required to implement WASH FIT and to draw specific links between changes in outputs, outcomes, and impacts. Short-term opportunities exist to improve evidence by more comprehensive reporting of WASH FIT assessments and exploiting data on health impacts within health management information systems. In the long term, we recommend experimental studies. This evidence is important to ensure that funding invested for WASH FIT implementation is used cost-effectively and that opportunities to adapt and refine WASH FIT are fully realized as it continues to grow in use and influence.

Formation behavior of PCDD/Fs during waste pyrolysis and incineration: Effect of temperature, calcium oxide addition, and redox atmosphere.

The clean and efficient utilization of municipal solid waste (MSW) has attracted increasing concerns in recent years. Pyrolysis of MSW is one of the promising options due to the production of high-value intermediates and the inhibition of pollutants at reducing atmosphere. Herein, the formation behavior of polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD/Fs) during MSW pyrolysis and incineration was experimentally investigated and compared. The influence of reaction temperature, CaO addition, and redox atmosphere on PCDD/Fs formation were compared and discussed. The results showed as the pyrolysis temperature increased, the mass concentration and international toxicity equivalence quantity of PCDD/Fs initially peaked at ∼750 °C before declining. Most of the generated PCDD/Fs were concentrated in the liquid and gaseous products, accounting for ∼90% of the total. Among liquid products, octachlorodibenzo-p-dioxin (O8CDD), 2,3,4,7,8-pentachlorodibenzofuran and 1,2,3,4,6,7,8-heptachlorodibenzofuran (H7CDF) were the most crucial mass concentration contributors, while in gas products, high-chlorinated PCDD/Fs, such as O8CDD, octachlorodibenzofuran (O8CDF) and 1,2,3,4,6,7,8-H7CDF were predominant. Compared to incineration, the formation of PCDD/Fs was 7-20 times greater than that from pyrolysis. This discrepancy can be attributed to the hydrogen-rich and oxygen-deficient atmosphere during pyrolysis, which effectively inhibited the Deacon reaction and the formation of C-Cl bonds, thereby reducing the active chlorine in the system. The addition of in-situ CaO additives also decreased the active chlorine content in the system, bolstering the inhibiting of PCDD/Fs formation during MSW pyrolysis.

Should pipeline nitrous oxide be discontinued in secondary care: A cost-benefit analysis.

Background: Nitrous oxide (N2O) has seen a marked decline in its usage in recent years due to its adverse clinical effects. We audited the practice in our department to evaluate the N2O consumption and cost-effectiveness of its supply. Methodology: Electronic anesthesia records of all patients anesthetized in our main operating rooms in a typical month were reviewed retrospectively, and utilization of N2O was noted in addition to the patient demographics, surgical procedure, and specialty. Results: A total of 950 patients were anesthetized, and 3.1% received N2O. The annual usage was estimated to be 72,871 liters, with a leakage of 3,883,105 liters to the environment, posing a safety hazard and wasting 149,612.50 SAR. Conclusion: Notable costs and environmental benefits may be achieved by substituting a piped supply of N2O with portable E-cylinders on demand in operating rooms for rational use.

The influence of nanosunflower ash and nanowalnut shell ash on sustainable lightweight self-compacting concrete characteristics.

The absence of biodegradability exhibited by plastics is a matter of significant concern among environmentalists and scientists on a global scale. Therefore, it is essential to figure out potential pathways for the use of recycled plastics. The prospective applications of its utilisation in concrete are noteworthy. The use of recycled plastic into concrete, either as a partial or complete substitution for natural aggregates, addresses the issue of its proper disposal besides contributing to the preservation of natural aggregate resources. Furthermore, the use of agricultural wastes has been regarded as a very promising waste-based substance in the industry of concrete manufacturing, with the aim of fostering the creation of an environmentally sustainable construction material. This paper illustrates the impact of nano sunflower ash (NSFA) and nano walnut shells ash (NWSA) on durability (compressive strength and density after exposure to 800 °C and sulphate attack), mechanical properties (flexural, splitting tensile and compressive strength) and fresh characteristics (slump flow diameter, T50, V-funnel flow time, L-box height ratio, segregation resistance and density) of lightweight self-compacting concrete (LWSCC). The waste walnut shells and local Iraqi sunflower were calcinated at 700 ± 50 °C for 2 h and milled for 3 h using ball milling for producing NSFA and NWSA. The ball milling succeeded in reducing the particle size lower than 75 nm for NSFA and NWSA. The preparation of seven LWSCC concrete mixes was carried out to obtain a control mix, three mixtures were created using 10%, 20% and 30% NWSA, and the other three mixtures included 10%, 20% and 30% NSFA. The normal weight coarse aggregates were substituted by the plastic waste lightweight coarse aggregate with a ratio of 75%. The fresh LWSCC passing capacity, segregation resistance, and filling capability were evaluated. The hardened characteristics of LWSCC were evaluated by determining the flexural and splitting tensile strength at 7, 14 and 28 days and the compressive strength was measured at 7, 14, 28 and 60 days. Dry density and compressive strength were measured after exposing mixes to a temperature of 800 °C for 3 h and immersed in 10% magnesium sulphate attack. The results demonstrated that the LWSCC mechanical characteristics were reduced when the percentages of NWSA and NSFA increased, except for 10% NWSA substitution ratio which had an increase in splitting tensile strength test and similar flexural strength test to the control mixture. A minor change in mechanical characteristics was observed within the results of LWSCC dry density and compressive strength incorporating various NSFA and NWSA` contents after exposing to temperature 800 °C and immersed in 10% magnesium sulphate attack. Furthermore, according to the findings, it is possible to use a combination of materials consisting of 10-20% NSFA and 10-20% NWSA to produce LWSCC.

Effects of carbon-based conductive materials on semi-continuous anaerobic co-digestion of organic fraction of municipal solid waste and waste activated sludge.

Organic fraction of municipal solid waste (OFMSW) and waste activated sludge (WAS) are the most produced organic waste streams in urban centres. Their anaerobic co-digestion (AcoD) allows to generate methane (CH4) and digestate employable as renewable energy source and soil amendment, respectively, fully in accordance with circular bioeconomy principles. However, the widespread adoption of such technology is limited by relatively low CH4 yields that fail to bridge the gap between benefits and costs. Among strategies to boost AcoD of OFMSW and WAS, use of conductive materials (CMs) to promote interspecies electron transfer has gained increasing attention. This paper presents one of the few experimental attempts of investigating the effects of four different carbon(C)-based CMs (i.e., granular activated carbon - GAC, graphite - GR, graphene oxide - GO, and carbon nanotubes - CNTs) separately added in semi-continuous AcoD of OFMSW and thickened WAS. The presence of C-based CMs has been observed to improve CH4 yield of the control process. Specifically, after 63 days of operation (concentrations of GAC and GR of 10.0 g/L and of GO and CNTs of 0.2 g/L), 0.186 NL/gVS, 0.191 NL/gVS, 0.203 NL/gVS, and 0.195 NL/gVS of CH4 were produced in reactors supplemented with GAC, GR, GO, and CNTs, respectively, compared to 0.177 NL/gVS produced in the control process. Likewise, at the end of the test (i.e., after 105 days at concentrations of C-based CMs half of the initial ones), CH4 yields were 0.193 NL/gVS, 0.201 NL/gVS, 0.211 NL/gVS, and 0.206 NL/gVS in reactors supplemented with GAC, GR, GO, and CNTs, respectively, compared to 0.186 NL/gVS of the control process. Especially with regard to GR, GO, and CNTs, results obtained in the present study represent a significant advance of the knowledge on the effects of such C-based CMs to realistic and scalable AD process conditions respect to previous literature.

Cultural worldviews and waste sorting among urban Chinese dwellers: the mediating role of environmental risk perception.

Objective: Waste sorting has received considerable attention in recent decades. However, research on the mechanisms underlying the relationships among cultural worldview, environmental risk perception, and waste sorting is rather scarce. This study aims to explore the cultural worldviews, environmental risk perception, and waste sorting among urban Chinese and their mechanisms. Methods: This was a cross-sectional study involving 744 urban Chinese residents (371 men and 373 women). A questionnaire was utilized to measure cultural worldviews, environmental risk perception, and waste sorting. Pearson correlation analysis and structural equation modeling were used to examine the relationship between cultural worldviews, perceptions of environmental risk, and waste sorting. Results: Waste sorting had a relatively insignificant negative relationship with fatalism and individualism. The correlation between environmental risk perception and cultural worldviews was negative except for egalitarianism, and the correlation between hierarchy and environmental risk perception was higher than the others, while individualism was higher than fatalism. Heightened environmental risk perception mediates the relationship between egalitarianism and waste sorting. Reduced environmental risk perception mediates the relationship between hierarchy and waste sorting, and mediates the relationship between individualism and waste sorting. Conclusion: These new findings provide initial support for the mediating role of environmental risk perception in the relationship between cultural worldviews and waste sorting. Both theoretical and practical implications for understanding the psychological mechanisms of waste sorting are discussed.

Co-pyrolysis of alkali-fused fly ash and corn stover to synthesize biochar composites for remediating lead-contaminated soil.

Fly ash (FA) is mainly composed of silica, alumina, and other metal oxide components, and has a positive stabilizing effect on soil heavy metals. Biochar composites produced from FA and corn stover (CS) can improve its remediation performance. Therefore, a batch of biochar composites (alkali-fused FA-CS biochars, ABs), synthesized via co-pyrolysis of CS and alkali-fused FA (AFFA) at different temperatures of 300, 500, and 700 °C (AB300-1, AB500-1, and AB700-1) and CS to AFFA mass ratios of 10:1, 10:2, and 10:5 (AB500-1, AB500-2, and AB500-5), was used to remediate lead (Pb)-contaminated soil. Compared with pristine biochars (BCs), ABs were enriched with oxygen-containing functional groups (Si-O-Si and Si-O) and aromatic structures. The ABs prepared at lower pyrolytic temperature (≤500 °C) and lower ratio of CS to AFFA (10:1) showed higher yield and stability. The contents of Toxicity Characteristic Leaching Procedure (TCLP)-extractable Pb and DTPA-CaCl2-triethanolamine (DTPA)-extractable Pb were generally lower in the soils amended with ABs than BCs. Compared with other ABs such as AB300-1, AB500-2, AB500-5, and AB700-1, the soil amended with AB500-1 had lower contents of TCLP and DTPA-extractable Pb (24% reduction), exhibiting superior performance in stabilizing Pb in the soil. The gradual decrease of DTPA-extractable Pb content in the soil with increasing dosage of AB500-1 amendments suggests that AB500-1 facilitated the conversion of bioavailable Pb to the stable and less toxic residual fractions. Specifically, the highest percentage of residual fraction of Pb in soil amended with AB500-1 was 14%. Correlation analyses showed that the soil DTPA-extractable Pb content decreased with the increase of soil pH and cation-exchange capacity (CEC) value. ABs stabilize Pb in the soils mainly via electrostatic attraction, precipitation, cation-π interaction, cation exchange, and complexation. These findings provide insights for producing functionalized biochar composites from industrial waste like FA and biomass waste for remediating the soils polluted by heavy metals.

A pilot study on psychosocial factors and perceptions of organizational health among a sample of U.S. waste workers.

Solid waste workers encounter a number of occupational hazards that are likely to induce stress. Thus, there are likely to be psychosocial factors that also contribute to their overall perceptions of organizational health. However, attitudes regarding the aforementioned among solid waste workers' have not been assessed. This descriptive, cross-sectional pilot study operationalized the INPUTS Survey to determine workers' perceptions of organizational health and other psychosocial factors of work. Percentage and mean responses to each INPUTS domain are presented in accordance with their survey manual. Pearson's chi-squared tests were run on count data; Fisher's exact tests were run for count data with fewer than five samples. ANOVAs were run on the continuous items. Due to a relatively low sample size (N = 68), two-sided p values < 0.1 were considered statistically significant. Most solid waste worker participants reported high decision authority, that they perceived their management to prioritize workplace health and safety, and had high job satisfaction. However, perceptions of support for health outside of the realm of occupational safety and health was lower. Addressing traditional occupational health hazards continues to take precedence in this industry, with less of a focus on how the social determinants of health may impact workplace health.

Hospital Wastes as Potential Sources for Multi-Drug-Resistant ESBL-Producing Bacteria at a Tertiary Hospital in Ethiopia.

The hospital environment is increasingly becoming an important reservoir for multi-drug-resistant (MDR) Gram-negative bacteria, posing serious challenges to efforts to combat antimicrobial resistance (AMR). This study aimed to investigate the role of hospital waste as a potential source of MDR ESBL-producing bacteria. Samples were collected from multiple sources within a hospital and its vicinity, including surface swabs, houseflies, and sewage samples. The samples were subsequently processed in a microbiology laboratory to identify potential pathogenic bacteria and confirmed using MALDI-TOF MS. Bacteria were isolated from 87% of samples, with the predominant isolates being E. coli (30.5%), Klebsiella spp. (12.4%), Providencia spp. (12.4%), and Proteus spp. (11.9%). According to the double disc synergy test (DDST) analysis, nearly half (49.2%) of the bacteria were identified as ESBL producers. However, despite exhibiting complete resistance to beta-lactam antibiotics, 11.8% of them did not test positive for ESBL production. The characterization of E. coli revealed that 30.6% and 5.6% of them carried blaCTX-M group 1 type-15 and blaNDM genes, respectively. This finding emphasizes the importance of proper hospital sanitation and waste management practices to mitigate the spread of AMR within the healthcare setting and safeguard the health of both patients and the wider community.

Feasibility of Enzymatic Protein Extraction from a Dehydrated Fish Biomass Obtained from Unsorted Canned Yellowfin Tuna Side Streams: Part II.

The enzymatic extraction of proteins from fish biomasses is being widely investigated. However, little or almost no research has paid attention to the exploitation of unsorted fishery biomasses. This work is part of a larger study, Part I of which has already been published, and focuses on an extensive characterization of two collagenous samples, namely gelatin (G) and hydrolyzed gelatin peptides (HGPs), extracted from a dehydrated fish biomass coming from unsorted canned yellowfin tuna side streams. The results indicate crude protein fractions of 90-93%, pH values between 3 and 5, white-yellow colors, collagen-like FTIR spectra, and 17% in terms of total amino acid content. Viscosity and the study of dynamic viscous-elastic behavior were analyzed. Thermo-gravimetric analysis was performed to assess the residual ashes. Both samples were investigated to determine their molecular weight distribution via size-exclusion chromatography, with a higher total average molecular weight for G compared to HGPs, with values of 17,265.5 Da and 2637.5 Da, respectively. G demonstrated technological properties similar to analogous marine gelatins. HGPs demonstrated antioxidant activity as per FRAP assay. All the results open up new perspectives for the potential use of these substances in biodegradable packaging, dietary supplements, and skin care cosmetics.

Shrimp Waste Upcycling: Unveiling the Potential of Polysaccharides, Proteins, Carotenoids, and Fatty Acids with Emphasis on Extraction Techniques and Bioactive Properties.

Shrimp processing generates substantial waste, which is rich in valuable components such as polysaccharides, proteins, carotenoids, and fatty acids. This review provides a comprehensive overview of the valorization of shrimp waste, mainly shrimp shells, focusing on extraction methods, bioactivities, and potential applications of these bioactive compounds. Various extraction techniques, including chemical extraction, microbial fermentation, enzyme-assisted extraction, microwave-assisted extraction, ultrasound-assisted extraction, and pressurized techniques are discussed, highlighting their efficacy in isolating polysaccharides, proteins, carotenoids, and fatty acids from shrimp waste. Additionally, the bioactivities associated with these compounds, such as antioxidant, antimicrobial, anti-inflammatory, and antitumor properties, among others, are elucidated, underscoring their potential in pharmaceutical, nutraceutical, and cosmeceutical applications. Furthermore, the review explores current and potential utilization avenues for these bioactive compounds, emphasizing the importance of sustainable resource management and circular economy principles in maximizing the value of shrimp waste. Overall, this review paper aims to provide insights into the multifaceted aspects of shrimp waste valorization, offering valuable information for researchers, industries, and policymakers interested in sustainable resource utilization and waste-management strategies.

Exploring the geotechnical and microstructural properties of composite mixtures for landfill liner materials: an experimental investigation.

The present study directs the need for the development of an economical composite mix comprised locally available soil and industrial waste which satisfy the design parameters of the municipal solid waste (MSW) landfill. The local soil, bentonite, and fly ash mixtures are mixed in different proportions to evaluate the geotechnical and microstructural characteristics for suggesting an optimum composite mix that fulfills the design parameters of landfill liners. The curing periods of different mixes are also considered while evaluating the unconfined compressive strength (UCS) characteristics. The microstructure of the mixtures is examined using advanced imaging techniques, including X-ray diffraction (XRD), scanning electron microscopy (SEM), and energy-dispersive X-ray spectroscopy (EDAX) to gain insights into the changes at the microscale level due to the inclusion of fly ash. It is observed that soil-bentonite-fly ash composite mix in a ratio of 65:15:20 aligns with the optimal design characteristics required for a landfill liner. Notably, for this composite mix, both liquid limit (LL) and plastic limit (PL) show a significant increase of 48.57% and 32.33% respectively, while the optimum moisture content (OMC) rises by 11.25%. Conversely, maximum dry density (MDD) experiences an 8.79% decrease. Moreover, the free swell index (FSI) escalates by 113%, whereas hydraulic conductivity (HC) records a substantial reduction of 96.04%. Moreover, the UCS exhibited a notable increase of 209% after a 28-day curing period. The highest strength is achieved initially by soil mixed with 20% fly ash, followed by a blend containing 15% bentonite. Therefore, proper fly ash content in filler and other binder materials is an effective and sustainable approach that not only solves the disposal issue but also enhances the material's engineering characteristics, justifying its suitability to be used as a landfill liner.